Dodge Challenger Forum banner

1 - 20 of 52 Posts

·
Registered
Joined
·
169 Posts
Discussion Starter #1
So today I finally got my car on the dyno after a 4 day wait. I feel I got some impressive numbers, maybe even a little high.

448 hp and 450 tq.

Everyone seemed to be really impressed with the Stock dyno numbers.

Stock car, 1000 miles, 6MT, 4th gear pull.

 

·
Registered
Joined
·
2,674 Posts
I must say, that is very impressive! Congrats!
 

·
Registered
Joined
·
1,710 Posts
Hell yeah that's impressive.
 

·
Registered
Joined
·
202 Posts
I would get it dynoed again, somewhere else. I had mine done too and it made 478 hp.to the wheels... They call them hero dyno's.
 

·
Premium Member
Joined
·
1,319 Posts
uhh yeah Id get a second opinion. my 392 supercharged only made 490 something hp on a mustang dyno. 555 on a dynojet
 

·
Registered
Joined
·
169 Posts
Discussion Starter #7
I knew it was a bit high, this was even on a Mustang Dyno. The good thing it shut all the Hemi haters up. I was expecting 370 at the worst and 400 at the best.
 

·
Premium Member
Joined
·
5,641 Posts
Wow

445 HP and 450 Q at the wheels on a stocker. Did I read that right?
 

·
Registered
‘13 Challenger SRT 6M
Joined
·
2,817 Posts
I knew it was a bit high, this was even on a Mustang Dyno. The good thing it shut all the Hemi haters up. I was expecting 370 at the worst and 400 at the best.
Usually Mustang Dynos ain't THAT generous. Something stinks here-fishy! I have a 392 and the few other guys I know that have them dynoed "pre mods" at 405-415 to the wheels.


Sent from AutoGuide.com App
 

·
Premium Member
Joined
·
253 Posts
dude congrats you have a Wednesday car. my numbers were not that good but very similar on 2 dynos so good luck with it you lucked out and have a strong one.
 

·
Registered
Joined
·
456 Posts
congrats. you smashed my numbers of 438/415 stock. enjoy it.
 

·
Registered
Joined
·
4,293 Posts
You better go out and run 1/4 mile times with 115+ trap speeds before I believe your dyno numbers ;)
 

·
Registered
Joined
·
3,733 Posts
Just put mine on the dyno a few minutes ago. With the 180 T-Stat, LMI fender pull CAI and slightly tweeked canned 93 tune it made 440/440 SAE on a Dynojet.
 

·
Registered
‘13 Challenger SRT 6M
Joined
·
2,817 Posts
Just put mine on the dyno a few minutes ago. With the 180 T-Stat, LMI fender pull CAI and slightly tweeked canned 93 tune it made 440/440 SAE on a Dynojet.
NICE bro!! Very nice! Stock exhaust with this?


Sent from AutoGuide.com App
 

·
Registered
Joined
·
70 Posts
I do have a few questions about the results:
What was the Ambient Air Temp
What was the Humidity
What was the Barametric Perssure
What was the Altitude
These things are a factor in the results.
 

·
Registered
Joined
·
169 Posts
Discussion Starter #19
I do have a few questions about the results:
What was the Ambient Air Temp
What was the Humidity
What was the Barametric Perssure
What was the Altitude
These things are a factor in the results.
Air temp right around 70
Humidity around 30
Barametric pressure no idea
Altitude 3200
 

·
Registered
Joined
·
4,293 Posts
I do have a few questions about the results:
What was the Ambient Air Temp
What was the Humidity
What was the Barametric Perssure
What was the Altitude
These things are a factor in the results.
If you look closely you will see he mentions SAE-corrected, which takes those variables into effect to essentially standardize the results.
 
1 - 20 of 52 Posts
Top